FR-9.17 to FR-9.19 state the screen-size contract: size is measured, the
legibility floors are absolute, and touch is a first-class input.
NFR-12 to NFR-14 state what the build now guarantees — pinned images, no
source that exists only under gen/, and BLE Java locked to the crate.
Three corrections to the spec, all of them places where it described a
plan the code did not follow:
The stack table still named tauri-plugin-blec. The code uses btleplug
directly and has since the BLE crate was written; blec wraps it in its
own device model, which crates/ble would then have to be written against
twice. Recorded with the reason, not silently edited.
RISK-1 (btleplug's Android backend is the least mature part of the stack)
is partly retired rather than closed: the target builds, the Java is
version-locked and the JNI init is symbol-checked in CI. A scan and a
connect on real hardware are still unproven, so TASK-4 keeps that half
and says exactly what is left — install on a phone, find the D100 and
both pods, and survive a screen-off.
NFR-11 is honest about being coarser on Android. FLAG_KEEP_SCREEN_ON is
held for as long as the app is foregrounded, not scoped to the ride as
the desktop inhibitor is. It needs no permission and cannot leak, but it
is not what the requirement describes, so the requirement says so.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Speed now comes from the drivetrain and the load from the road, which is
the way round a bike actually works.
Speed is cadence x development, filtered lightly. Power, not cadence,
decides whether the rider is driving it: on a direct-drive trainer the
flywheel keeps the cranks turning after they stop, so cadence alone reads
a healthy 80 rpm for someone doing nothing. Below 15 W the speed runs
down to whatever the gradient sustains on no power - zero uphill, a real
freewheeling speed on a descent. Stopping on a 3.5% climb used to settle
at 22 km/h and stay there, because the model wanted to decelerate and a
blend toward the flywheel speed outvoted it; that blend is gone.
The D100 sends no cadence over FTMS - it is a rebadged Magene T110 with
cadence disabled in firmware (qdomyos-zwift#3282) - so it is inferred
from wheel speed, which one sprocket and no freewheel make exact. Its
Zwift channel does carry cadence, and is now greeted with RideOn and
subscribed on every notifying characteristic, so a measured value is used
where one arrives.
The load is commanded as power, not gradient. The trainer declares
50-600 W in 1 W steps against 0-6% inclination in 0.1% steps refusing
negatives, and whether it acts on 0x11 at all is still unconfirmed. Its
power target is a ceiling rather than a setpoint, which is very nearly
what a road is: exceed it and the surplus becomes speed. Gravity travels
on the same channel as watts, so nothing is lost by leaving 0x11 alone.
LoadChannel keeps the gradient path selectable and tested.
Virtual shifting reaches the trainer for the first time. The physics
load model was written but never called, and a paddle press both shifted
a gear in Rust and nudged the gradient in the webview - the shift
silently, the tilt visibly, so the paddles looked like a gradient trim.
Also: a fixed 12 W drivetrain loss, held as a power because that is how
it presents; crank length, so a gear can be reported as the force it puts
under the foot; gear and pedal force on the ride screen; a drag-race
profile for testing gearing on the flat.
Two readout bugs fixed on the way. The rolling windows were trimmed by
timestamp but fed on a fixed timer, so every second spent on the ride
screen before starting pushed samples at t=0 that could never expire -
speed read a fraction of the truth for the first 45 s. And the headline
speed was a 45 s mean, which took most of a minute to show a gear change.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Gears are expressed as an offset to the commanded gradient, leaving the
physics on the route's true gradient so shifting changes effort, not speed.
Neutral gear commands exactly the route gradient, so an un-shifted ride is
unchanged.
Cadence is not in FTMS on this trainer but is on its Zwift channel, decoded
against captured frames. The undeclared FTMS trailing bytes were ruled out:
wheel RPM restated at a fixed 73.8x speed.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
Standalone binary embeds the frontend, avoiding the dev-server dependency
that made the window fail to load.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
dtourolleandClaude Opus 5